What is the difference between kitec and PEX?

What is the difference between kitec and PEX?

Is kitec plumbing the same as PEX? PEX is an abbreviation of cross-linked polyethylene, a type of plastic often used to make pipes. Kitec plumbing is made from layers of aluminum and PEX sandwiched together, but there are other forms of PEX plumbing that are perfectly acceptable for modern homes.

Can I use PEX fittings on kitec?

KITEC piping has a layer of aluminum, sandwiched between 2 plastic layers (PEX-AL-PEX or PE-AL-PE). No other fittings are compatible with KITEC piping. Push fit fittings (SharkBite) do not fit KITEC piping.

How do you identify kitec pipe?

How do I Identify Kitec Plumbing? Most Kitec plumbing can be identified by its bright orange (hot water) and bright blue (cold water), which were the most common colours; however, it was also sold in red, blue, gray and black.

Does kitec fittings mean kitec pipes?

Kitec pipe was manufactured in two colors: blue for cold water and orange for hot water. The side of the pipe is typically marked “IPEX” and the fittings, stamped “Kitec”, may be recognized by looking at the pipe and fittings.

Is Poly B the same as kitec?

Commonly used in domestic water, and heating system, this is reminiscent of another piping system which was sold under the brand name Poly-B. You can identify Kitec piping by its blue or orange colour. Typically blue was used for water lines and orange was used in hot water heating systems.

When was kitec banned?

Kitec plumbing systems, which were recalled due to defects back in 2005, were installed in hundreds of thousands of homes across Canada – including many thousands here in the Greater Toronto Area.

Are all orange pipes kitec?

Although Kitec pipes were sold under many names, they almost all have a few things in common that makes Kitec relatively easy to identify: Colour. Most Kitec pipes are either bright orange or bright blue.

Does insurance cover kitec plumbing?

Depending on the terms of your home insurance policy, you may be covered in the event of a flood caused by burst or leaking Kitec piping in your home. Some home insurers have been willing to cover all or part of the cost to replace Kitec piping to avoid having to eventually pay out a claim for water damage.

How much was the kitec settlement?

The settlement included $25 million US for legal fees, notices and other administration, leaving $100 million US plus interest to pay claims for damage caused by leaks and floods and replacing the fixtures and pipes.

What is the pressure rating of KITEC composite pipe?

KiTEC Composite Pipes conform to IS : 15450-2004 “Standard Specification for Polyethylene/ Aluminium/ Polyethylene (PE-AL-PE) Composite Pressure Pipe.”. KiTEC Composite Pipes are having pressure rating of 13.8 Kg/Cm 2 at 23 oC. and 11.0 Kg/Cm 2 at 60 oC.

Who is the manufacturer of KITEC water supply pipe?

KITEC is a brand of water supply pipe and brass fitting which was manufactured by Canadian pipe manufacturer IPEX. The brass fittings were produced from 1995 until 2005, when IPEX issued a recall on the fittings due to failures.

When was KITEC piping installed in your home?

Kitec plumbing is a polymer pipe, typically installed in homes between 1995 and 2007, that is prone to spontaneously burst. While you can take steps to prevent leaks from these this type of piping, Kitec pipes are more likely to crack at any minute and cause major damage to your home. A major leak…

Are there any other fittings that work with KITEC?

No other fittings are compatible with KITEC piping. Push fit fittings (SharkBite) do not fit KITEC piping. It would also be foolish to try to replace fittings and continue to use piping, which in my opinion and statistical information, is equally problematic.

Share this post